Easy, Affordable Financing Available Now!

   Apply Now

New Holland Durabine™ 416 PLUS

New Holland Durabine™ 416 PLUS

Double tap to zoom

New Holland Durabine™ 416 PLUS

 

Features

REDESIGNED FOR FASTER SPEED
Durabine™ PLUS Series disc headers take advantage of faster speeds on Speedrower® PLUS windrowers without compromising cutting and conditioning quality.

CLEAN & CLOSE CUTTING
The MowMax™ II PLUS true modular cutterbar found on Durabine PLUS heads provides an even cleaner cut with faster tip speed and a lower-profile compared to previous models.

LEGENDARY PERFORMANCE
HS Series Haybine sickle headers continue the legacy of impeccable cutting performance, fast drying, and time-tested reliability.

UNIFORM, FAST-DRYING SWATHS
Choose the best conditioning system for your crops – rubber chevron rolls, steel chevron rolls, or high-contact chevron rolls.

DURABINE™ PLUS DISC HEADERS

CLEAN AND CLOSE CUTTING
To maximize productivity, the all-new MowMax™ II PLUS true modular cutterbar delivers a cleaner cut. Longer knives extend each module’s cutting diameter by nearly an inch and turn with 14 mph faster tip speed (195 mph vs 181 mph) than the previous series at 2,600 disc rpm. For better crop-to-knife engagement, the cast rock guards were reshaped. To improve cutting in light or late-season crops, the profile of the cutterbar was lowered by bringing the discs closer to the cutterbar with new low profile ShockPRO™ hubs. Along with the longer knives, this design is more productive in down and tangled crops as the cutting height was lowered nearly 30%, leaving less uncut crop behind.

To optimize crop flow and conditioning, all-new Durabine 416 PLUS disc rotation delivers crop in four streams into the new Constant Flow Auger. The result? More even windrows with improved center fill. Crop wrapping is prevented and conditioning roll end wear in abrasive conditions is reduced.

3-YEAR MOWMAX CUTTERBAR WARRANTY
With every Durabine PLUS disc head, you get the peace of mind provided by 36 months of cutterbar warranty coverage. Coverage includes one full year of base factory warranty, plus two additional full years of MowMax II PLUS disc cutterbar warranty. It’s a New Holland exclusive – you’re backed by the best in the business.

SAVE TIME WITH THE QUICKMAX™ KNIFE-CHANGE SYSTEM
When it comes to haymaking, your time is precious. The patented QuickMax System is standard and allows you to quickly change a damaged knife or flip an entire set of knives so you’re back to clean cutting in seconds. Fast knife changes are done with a 180-degree rotation of the discs and the use of a special tool stowed on the head, which pries down the spring plate to release the knife from the knife nut. Knife-lock technology assures knife retention in the most difficult conditions.

AVAILABLE REPLACEMENT KNIVES
Durabine PLUS Series heads can be equipped with knives that best fit your crop conditions and soil types. All knives work with the QuickMax knife change system and feature two cutting edges so they can be flipped for double the life.
• 12- and 7-degree twisted smooth knives – 12-degree twisted smooth knives come standard for normal cutting conditions, while 7-degree twisted smooth knives offer clean cutting and reduced blowdown in light or short crops. University studies have shown that less knife twist can also help reduce ash content. New Holland recommends 7-degree smooth twisted knives in rocky or stony conditions.
• 12- and 7-degree twisted serrated knives – Serrated knives offer extended wear in abrasive crop conditions and may improve cut quality.

SMOOTH AND CONSISTENT FEEDING
A full-length constant flow auger quickly moves crop away from the cutterbar for increased capacity, optimum feeding, uniform conditioning, and an evenly-distributed windrow. This heavy-duty, 20-inch auger features thick, 5/16-inch flighting with reinforced gussets on the back to handle the heaviest crops with ease. For optimal crop flow, multiple paddles are staggered throughout the auger. To protect the conditioning rolls, a rock door is located behind the auger, which can be opened to allow debris to drop out, as well as reduce turbulence in very light crop conditions.

IMPRESSIVE HEADER POWER
When the conditions get tough, rest assured that Speedrower 220 PLUS and 260 PLUS windrowers will maintain impressive cutting performance. In comparison to prior models, the new Danfoss® Hydraulic electronically-controlled pump provides increased hydraulic flow while turning at a slower rated engine speed. To provide quieter header drive and improved oil flow, the header drive is transmitted through a hydraulic distribution block and low back-pressure flat-faced couplers. High-performance Bondioli hydraulic motors on the head increase the header drive working pressures and provide superior reliability.

VERSATILE, MODULAR CONDITIONING SYSTEM
Diverse crop harvesting is no problem for Durabine PLUS Series disc headers. You can change conditioning modules quickly to suit crops and maximize quality or remove the conditioning module entirely and outfit the header with a closure kit for wide swaths of non-conditioned hay. The large, 10.4-inch diameter rolls with a chevron-lug profile grip the crop and provide even flow through the rolls for uniform conditioning and fast-drying swaths or windrows. Tailor roll pressure to crop yields without tools with the turn of a hand crank that delivers consistent, thorough conditioning for all crops. All roll conditioning systems feature the proven torsion-bar roll-pressure system with over-center linkage that momentarily releases roll pressure, allowing slugs of crop or foreign objects to pass without plugging for non-stop mowing.

• Rubber chevron rolls – Choose gentle chevron rubber rolls for full-stem crimping and cracking of high-value legume crops. The rubber compound and wide chevron lug profile provide gentle handling to protect delicate, high-value leaves for maximum forage quality.
• Steel chevron rolls – Durable chevron steel rolls are designed for use in all crop types but show a real advantage in cane-type crops, grain forages, and extra-tall grass crops. The steel chevron lug profile provides aggressive full-stem crimping, and the rugged, all-steel construction resists wear in abrasive crops and conditions.
• High-contact urethane rolls – When full-stem crushing is needed for fast drying, New Holland high-contact rolls are specially machined for an exact fit for complete stem conditioning. These rolls feature machined chevron grooves to grip and move crop effectively without sharp angles that can damage valuable leaves.

UNIFORM, FAST-DRYING SWATHS
Fast drying requires the crop to be evenly distributed over a wide swath. Durabine PLUS disc headers provide extra crop control surfaces behind the conditioning system. The new swath baffle is 8 inches longer and has additional adjustable control surfaces that let you form the perfect swath for nearly any condition. For wide swaths, the baffle is lowered so the adjustable swath spreading wedges engage the crop stream to improve uniformity. When windrowing, the baffle is raised so the adjustable windrow fins engage the crop and improve center fill. Windrow shields are optimized to create a tunnel effect with a fluffing baffle, guiding crop into the windrow and creating a well-defined windrow edge.

Specifications

Dimensions & Weights  
MODEL Durabine™ 416 PLUS
Cutting width ft. in. (m) 16' 3" (4.95)
Overall width ft. in. (m) 16' 7" (5053)
Weighting with conditioning system lbs. (kg) 5114 (2319)
Weight less conditioning system lbs. (kg)
Durabine PLUS MowMax™ II PLUS Cutterbar  
Cutting width ft. in. (m) 16' 3" (4.95)
Cutting height range in. (mm) 0.5-3.3 (13 - 86)
Cutting angle  0 to -10 degrees
Number of discs 10
Maximum disc speed rpm 2600
Number of reversible swing-away knives
Knife tip speed mph (kph) 195 (314)
Flotation Hydraulic adjustment from cab
ShockPRO™ Disc Drive Protection System Standard
3-Year MowMax Factory Cutterbar Warranty Standard
Haybine Cutterbar  
Cutting width ft. in. (m)
Cutting height range in. (mm)
Cutting angle
Type
Knives
Guards
Skid shoes
Drive type
Speed spm
Stroke in. (mm)
Haybine Reel  
Type
Adjustments
Mechanical drive rpm
Hydraulic drive (optional) rpm
Speed adjustment (mechanical)
Diameter in. (mm)
Drive type
Tine bars
Bushings / bearings* in. (mm)
Auger  
Auger diameter in. (mm) 20 (508)
Auger type Floating
Conditioning Systems  
Roll types Chevron-pattern rubber or steel
Roll length in. (mm) 102 (2591)
Roll diameter in. (mm) 10 .16 (258)
Roll speed rpm 938
Roll pressure Hand crank
Roll gap Adjustable stop-bolt
Roll drive Spur gearbox and PTOs
Windrow/swath width in. (mm) 38 to 96 (965 to 2438)